92-95 MAZDA MX3 JDM 2.4\" 6-HOLE AFTERMARKET STEERING WHEEL HUB BOSS ADAPTER KIT for Sale

92-95 MAZDA MX3 JDM 2.4\
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Price: $19.49

KTAUTORACING

This is 1 piece of aftermarket steering wheel hub boss adapter kit for the following vehicles:92-95 Mazda MX3

Features:

  • Made of high quality light-weight aluminum with rubber,
  • 60.58 mm/2.38 in in thickness and approximate 3.5" in diameter.
  • The 6 holes pattern (70mm bolt spread) is compatible with most aftermarket racing steering wheels WITH THE SAME BOLT SPREAD ONLY (such as Momo and Nardi) and ball bearing type quick release kit, and it is a necessary part if you want to install the aftermarket racing steering wheel.
  • Comes with 1 x hub boss kit, 6 screws and 1 wrench for installation.
  • Instruction is not included with this package and professional installation is highly recommended.

Generic installation steps (additional steps might be needed depending on different cars, but here is the basic steps for your reference):

Step 1: Preparation

Before you remove the steering wheel, disconnect the negative terminal of your battery to prevent your horn from going off during installation.

Step 2: Removal of the Horn



Stick your flat head screw driver into the slit of the horn button and pry it out carefully. It should pop out with ease. Then disconnect the wire connections for the horn and place the horn button aside. (If you car has air bag, additional steps might be needed, and you should have professional finish the installation.)

Step 3: Unbolting the steering wheel:

After taking out the horn, it should look like the photo above, unscrew all the bolts and then use your 19mm socket with breaker bar to unbolt the steering nut in the middle. Be careful as it is fairly tight and be careful not to smash your windscreen with the breaker bar. Once the nut is off, pull on the steering wheel and rock the steering wheel left to right and up and down to loosen it. It will be very tight and might need some force.

Step 4: Attaching the hub boss kit and aftermarket steering wheel:



Now you will need to do this step carefully as you want the steering wheel to be straight. If you are off by a hole, your steering wheel be pulled to one side while driving straight, and you\'ll have to reinstall the wheel again. Place the boss onto the column and pull the horn wires through the middle as you don\'t want them to be stuck inside the boss kit when you install the horn. Align the steering wheel accordingly by rotating the boss kit until the steering wheel is in the right place. Then use your hex key and secure the steering wheel in place.

Step 5: Wiring up the horn:



Connect the 2 little wires from the boss kit and the steering wheel to the horn. It doesn\'t matter which wires go to here and there. Once that\'s done drop the horn button into place. Make sure the metal parts of the horn button are not touching the other end. Reconnect the battery to make sure everything is working as it should.

SHOP CATEGORIES EXHAUST - EXHAUST MUFFLERS EXHAUST - TURBO WHISTLERS EXTERIOR - LICENSE FRAME RELOCATORS EXTERIOR - SIDE MIRRORS INTERIOR - REARVIEW MIRRORS INTERIOR - SHIFT BOOTS INTERIOR - SHIFT KNOBS INTERIOR - WINDOW WINDER HANDLES LIGHTS - 4x4 WORKLIGHTS LIGHTS - CCFL HALO INVERTERS LIGHTS - CORNER LIGHTS LIGHTS - FOG LIGHTS LIGHTS - HALOGEN BULBS LIGHTS - HEADLIGHTS LIGHTS - HID LIGHTS - HID COMPONENTS LIGHTS - LED BULBS LIGHTS - LED DOME LIGHTS LIGHTS - LOAD RESISTORS LIGHTS - TAIL LIGHTS STEERING - HUB BOSS KITS STEERING - STEERING WHEELS

Powered by SoldEazy


Parts Search:

Follow